How do I reboot my Synology router?

How do I reboot my Synology router?

Use a paper clip to gently press and hold the RESET button for 4 seconds. Your Synology Router will then start a soft reset. When the soft reset is complete, launch a web browser on a computer that is being connected to your Synology Router via Ethernet. Enter “” in the address bar.

How do I access my Synology router?

Access SRM via the IP address of your Synology Router If you still cannot access your Synology Router via from a client device, you can access it using its default IP address “192.168. 1.1”.

Does Synology need to be connected to router?

Sure. No need for a router or an external connection. Assign static IP’s to all the devices, connect via a hub or switch and you’re good to go. You can add a router to assign the IP addresses (or some NAS devices have DHCP server capability- eg Synology).

How do I access Synology settings?


  1. Go to Control Panel > QuickConnect.
  2. Check the Enable QuickConnect box.
  3. If you do not have a Synology Account, click Log in to or register a Synology Account.
  4. Create your own QuickConnect ID in the QuickConnect ID field.
  5. If you do not see the QuickConnect DSM link, click Advanced and make sure DSM is enabled.

How long does Synology NAS take to reboot?

When rebooted, the blue light flashes (as expected) along with the LAN light. Boot takes probably a good 5 or 6 minutes and I can hear the HDD’s working occasionally during that time, but they don’t light up on the NAS. Eventually it’ll beep and the HDD lights will come on.

How do I reboot my NAS?

To Reboot the BlackArmor NAS:

  1. In the menu bar, select System, and then click Shut Down/Reboot.
  2. Click the Reboot button.
  3. Click the OK button to confirm your choice.
  4. A window opens notifying you that the system is ready to continue.
  5. Enter the administrator’s Username and password.
  6. Click the Login button.

How do I RESET my Synology network settings?

Mode 1: Reset administrator login credentials and network settings to default. Locate the RESET button on your Synology NAS. Press and hold down the RESET button for about 4 seconds until you hear a beep. Release the button immediately.

Does NAS have to be plugged into router?

Tip: While most NAS devices require an Ethernet connection to your network router, some models offer built-in Wi-Fi wireless connectivity and don’t need to be physically connected to a router.

How do I access Synology NAS via DDNS?

Setting up DDNS

  1. Go to Control Panel > External Access > DDNS.
  2. Click Add.
  3. A dialog box appears prompting you to edit the following settings:
  4. Click Test Connection to see if settings are correct.
  5. If you select Synology as the service provider, you can configure the following settings:
  6. Click OK to save and finish.

How do I Reset my Synology router?

Use the paper clip or pen to hold the reset button on the back of the NAS for about 4 seconds. Release the button when you hear a beep.

  • The NAS now starts again. Wait until you hear a new beep.
  • Open in an internet browser.
  • Set a new password for your account.
  • Follow the further steps on the screen and you can use your NAS again.
  • How to setup secure VPN to your Synology?

    How to set up a VPN. Log in to your Synology NAS. Go to Control Panel > Network > Network Interface. Click Create. Click Create VPN profile. Follow the on-screen wizard to import and connect to

    How to configure a Synology device?

    Initial Synology NAS Setup. We will quickly discuss how to setup a Synology NAS.

  • Data Protection&Monitoring – Synology NAS Setup Guide. Now that a storage pool,volume,and shared folder are created,we need to change a few settings to protect
  • Security – Synology NAS Setup.
  • Additional Recommendations – Synology NAS Setup.
  • How to use a Synology router as a media server?

    Click Set up router to launch the setup wizard.

  • Depending on the type of your router,do one of the following:
  • If your router doesn’t support UPnP,refer to step 3.
  • If your UPnP router has been tested to be compatible with Synology NAS device,click Apply when you see a summary of the router’s information.